Wooden Camera

Wooden Camera

Cable-less Gold Mount system for the RED Weapon, Scarlet-W, Raven cameras whichåÊutilizes an Anton Bauer brand plate with two D-Taps and the Wooden Camera pogo interface module. The assembly will attach without tools directly to the back of the RED Weapon/Scarlet-W/Raven camera, Base Expander Module, REDVolt Expander Module, and some third party modules like OMODs.

This system can be converted between center,åÊhigh, and low modes. Center mode is what is shown in the photos and is most appropriate for regular use. High and low modeshould be reserved for special circumstances.åÊHigh mode is where the battery plate sits above the back of the camera. Low mode is where the plate sits flush to the very bottom of the camera body meaning the Gold Mount batteries would actually stick out below the camera body.

The Cable-less Gold Mount will communicate percentage or voltage data to the camera's LCD display. Intelligent batteries like Anton Bauer Dionics, Switronix, and other batteries utilizing Anton Bauer protocol will allow for the module to communicate percentage data and estimated run time. Non-communicative batteries will only provide voltage data to the camera through our module.

2x D-Tap ports for accessory power
Cable-less V-Mount system for the RED Weapon, Scarlet-W, Raven cameras whichåÊutilizes an IDX brand plate with two D-Taps and the Wooden Camera pogo interface module. The assembly will attach without tools directly to the back of the RED Weapon/Scarlet-W/Raven camera, Base Expander Module, REDVolt Expander Module, and some third party modules like OMODs.

This system can be converted between high and low modes. High mode is where the battery plate sits above the back of the camera. Low mode is where the plate is configured to be flush with the top of the camera body leaving batteries in a very compact configuration. An important note is that the RED DSMC2 top handle will clear RED Brick batteries when our Cable-less V-Mount plate is configured in low mode.

The Cable-less V-Mount will communicate percentage or voltage data to the camera's LCD display. Intelligent batteries like RED Bricks, Blueshape, Switronix, PAG, and other batteries utilizing SMBUS or reversed SMBUS will allow for the module to communicate percentage data and estimated run time. Non-SMBUS batteries like some IDX and other low cost batteries will only provide voltage data to the camera through our module.åÊSpecial note: for PAG batteries, they must be put into RED mode by pushing the top button once, then push again a second time and hold until the top two LEDs on the ring are illuminated.

2x D-Tap ports for accessory power

Specifications:
Weight: 12oz.åÊ
Dimensions: 5 1/2" (142mm) x 3 3/8" (85mm) x 1 3/8" (33mm)

Cable-less Module Overview:

D-Box (Weapon/Scarlet-W/Raven, V-Mount) is a custom version of our popular D-Box that adds power distribution, standardized remote start/stop, and hot swap abilities for the RED DSMC2 cameras. The D-Box is completely tool-less for installation andåÊutilizes our Cable-less interface which attaches directly to the back of the camera body, Base Expander Module, REDVolt Expander Module, and the Offhollywood OMODs.

Connectors on the D-Box are contoured to match the Expander Modules'åÊwhich allow for all cables to be installed with no collisions.åÊThe module communicates with the camera and allows any ARRI standard start/stop trigger to be used with the 3pin Fischer port. The DC input on the D-Box is the same as the camera's LEMO allowing for an AC power supplyåÊor external power plate to be connected to power accessories and camera during a battery change. When both battery and DC input are utilized, the D-Box defaults to the DC input, leaving the battery fully charged.

Overview:

Authentic IDX V-Mount plate provides 2x D-Tap (unregulated) on the power plate itselfåÊbut we should note that one D-Tap is obscured by the right side power outputs. Inside the D-Box is a 10A fuse and replacement fuses are included.

D-Box Connections:

1. åÊ D-Tap - 12V Unregulated
åÊ åÊ åÊ åÊ -åÊThis slot can be swapped for Hirose, 2pin LEMO, oråÊ4pin LEMO

2. åÊåÊD-Tap - 12V Unregulated
åÊ åÊ åÊ åÊ -åÊThis slot can be swapped for Hirose, 2pin LEMO, oråÊ4pin LEMO

3. åÊ 2 pin LEMO - 12V Unregulated
åÊ åÊ åÊ åÊ - ARRI standard wiring

4. åÊ 2 pin LEMO - 12V Unregulated
åÊ åÊ åÊ åÊ - ARRI standard wiring

5. åÊ 3 pin Fischer - 24V Regulated
åÊ åÊ åÊ åÊ - Regulator built in to convert battery voltage to 24V
åÊ åÊ åÊ åÊ - Maximum 3A shared between the two 3pin Fischers
åÊ åÊ åÊ åÊ - ARRI standard start/stop capabilities

6. åÊ 3 pin Fischer - 24V Regulated
åÊ åÊ åÊ åÊ - Regulator built in to convert battery voltage to 24V
åÊ åÊ åÊ åÊ - Maximum 3A shared between the two 3pin Fischers
åÊ åÊ åÊ åÊ - ARRI standard start/stop capabilities

7. åÊ USB - 5v Regulated
åÊ åÊ åÊ åÊ - Provides 2A for iPhone/iPad charging

8. åÊ DC Input - 12-16V
åÊ åÊ åÊ åÊ -åÊDC input on the D-Box is the same as the camera's LEMO
åÊåÊ åÊ åÊ åÊ- Priority is given to DC InputåÊto preserve battery charge when both sources connected


D-Box (Weapon) Demonstration:

15mm Rod
from $ 20.00

15mm Rod

Wooden Camera Dovetail Clamp
Wooden Camera RED Male Pogo to Male LEMO LCD/EVF Cable
RED Male Pogo to Male LEMO LCD/EVF Cable (36") is a cable that allows the original RED displays to be attached to the new RED Weapon/Epic-W/Scarlet-W/Raven DSMC2 cameras. The male pogo connector attaches to the camera body without tools and the Male LEMO connector attaches to the original RED LCD/EVF using the standard 16pin LEMO connector. The braided, flexible cable makes positioning easy and is great for gimbal use.
Ultra Arm Monitor Mount (1/4-20 to 3/8-16, 5")åÊis an articulating arm with two sets of 25mm (1 inch)åÊdouble ball joints which allow a monitor or accessory to be positioned in just about any orientation.åÊTool-lessåÊ1/4-20 knobs on one end and 3/8-16 knob on the otheråÊwith non-slip rubber pads make setup quick and easy. Also included are two locating pins that can be installed on the 3/8-16 end turning it into an ARRI accessory mount compatible device!åÊBlack center thumbscrews ratchet to allow for easy positioning. The 5" title refers to the center extension length but actual length fully extended measures 289mm (11.4 inches).

Great for attaching LCDs, lights, audio recorders and much more!

Specifications:
Weight:åÊ317.5 g (0.7 lbs)
Dimensions:åÊ25.4 xåÊ101.6 x 228.6 mm ( 1 x 4 x 9 in)
RED Male Pogo to Female Pogo LCD/EVF Cable is a cable that allows the RED displays to be moved off the top of the RED Weapon/Epic-W/Scarlet-W/Raven and into a position more easily viewed. The male pogo connector attaches to the camera body without tools and the female pogo connector has a slotted design that can be bolted to any two 1/4-20 screws holes up to 54mm apart, center to center. 1/4-20 threaded holes are also found on the bottom of the female pogo connector for attaching to WC Magic Arms and Ultra Arms. The braided, flexible cable makes positioning easy and is great for gimbal use.
Wooden Camera - Microphone Shock Mount

Pass Through Top plate for RED Weapon, Epic Weapon (Epic-W), Scarlet Weapon (Scarlet-W), and Raven which provides 26pin LCD connection and 3pin trigger handle interface. Arrays of 1/4-20 holes in Red spacing, 3/8-16 holes for large accessories, and the ARRI standard accessory mount in several places. Attaches to top of camera by (4) 1/4-20 captured screws.


This product is great for adding mounting points to your DSMC2 camera and allows for other cage and cable components like theåÊSafety NATO Arm (Weapon/Epic-W/Scarlet-W/Raven) and RED Male Pogo To Female Pogo LCD/EVF Cables to be attached as well.

Includes:
(4) 1/4-20 x captured screws

A glimpse of the Pass Through Top Plate as used in our WiFi Side Plate demo:
Wooden Camera - Universal Offset Bracket

Wooden Camera - Universal Offset Bracket

by Wooden Camera
$ 65.00
Universal Offset Bracket attaches by an ARRI style accessory mount, 3/8-16 with locating pins adjacent. It can also attach by using two included 1/4-20 or 3/8-16 screws spaced up to 77mm (3 inches) apart center to center. Provides an ARRI style accessory mount spaced 100mm from the original mounting hole. Works great withåÊMicrophone Shock Mount.
Wooden Camera Cable-less V-Mount Blueshape

Wooden Camera Cable-less V-Mount Blueshape

by Wooden Camera
$ 695.00

(Weapon/Epic-W/Scarlet-W/Raven)

Cable-less V-Mount system for the RED Weapon, Epic Weapon (Epic-W), Scarlet Weapon (Scarlet-W), Raven cameras which utilizes an Blueshape brand plate with three D-Taps, one 5V USB, and the Wooden Camera pogo interface module. The assembly will attach without tools directly to the back of the RED Weapon/Scarlet-W/Epic-W/Raven camera, Base Expander Module, REDVolt Expander Module, and some third party modules like OMODs.


This system can be converted between high and low modes. High mode is where the battery plate sits above the back of the camera. Low mode is where the plate is configured to be flush with the top of the camera body leaving batteries in a very compact configuration. An important note is that the RED DSMC2 top handle will clear RED Brick batteries when our Cable-less V-Mount plate is configured in low mode.

The Cable-less V-Mount will communicate percentage or voltage data to the camera's LCD display. Intelligent batteries like RED Bricks, Blueshape, Switronix, PAG, and other batteries utilizing SMBUS or reversed SMBUS will allow for the module to communicate percentage data and estimated run time. Non-SMBUS batteries like some IDX and other low cost batteries will only provide voltage data to the camera through our module.

3x D-Tap ports for accessory power
1x 5V USB for additional accessories

D-Box (Weapon/Scarlet-W/Raven, GoldåÊMount) is a custom version of our popular D-Box that adds power distribution, standardized remote start/stop, and hot swap abilities for the RED DSMC2 cameras. The D-Box is completely tool-less for installation andåÊutilizes our Cable-less interface which attaches directly to the back of the camera body, Base Expander Module, REDVolt Expander Module, and the Offhollywood OMODs.

Connectors on the D-Box are contoured to match the Expander Modules'åÊwhich allow for all cables to be installed with no collisions.åÊThe module communicates with the camera and allows any ARRI standard start/stop trigger to be used with the 3pin Fischer port. The DC input on the D-Box is the same as the camera's LEMO allowing for an AC power supplyåÊor external power plate to be connected to power accessories and camera during a battery change. When both battery and DC input are utilized, the D-Box defaults to the DC input, leaving the battery fully charged.

Overview:

Authentic Anton Bauer GoldåÊMount plate provides 2x D-Tap (unregulated) on the power plate itselfåÊbut we should note that one D-Tap is obscured by the right side power outputs. Inside the D-Box is a 10A fuse and replacement fuses are included.

D-Box Connections:

1. åÊ D-Tap - 12V Unregulated
åÊ åÊ åÊ åÊ -åÊThis slot can be swapped for Hirose, 2pin LEMO, oråÊ4pin LEMO

2. åÊåÊD-Tap - 12V Unregulated
åÊ åÊ åÊ åÊ -åÊThis slot can be swapped for Hirose, 2pin LEMO, oråÊ4pin LEMO

3. åÊ 2 pin LEMO - 12V Unregulated
åÊ åÊ åÊ åÊ - ARRI standard wiring

4. åÊ 2 pin LEMO - 12V Unregulated
åÊ åÊ åÊ åÊ - ARRI standard wiring

5. åÊ 3 pin Fischer - 24V Regulated
åÊ åÊ åÊ åÊ - Regulator built in to convert battery voltage to 24V
åÊ åÊ åÊ åÊ - Maximum 3A shared between the two 3pin Fischers
åÊ åÊ åÊ åÊ - ARRI standard start/stop capabilities

6. åÊ 3 pin Fischer - 24V Regulated
åÊ åÊ åÊ åÊ - Regulator built in to convert battery voltage to 24V
åÊ åÊ åÊ åÊ - Maximum 3A shared between the two 3pin Fischers
åÊ åÊ åÊ åÊ - ARRI standard start/stop capabilities

7. åÊ USB - 5v Regulated
åÊ åÊ åÊ åÊ - Provides 2A for iPhone/iPad charging

8. åÊ DC Input - 12-16V
åÊ åÊ åÊ åÊ -åÊDC input on the D-Box is the same as the camera's LEMO
åÊåÊ åÊ åÊ åÊ- Priority is given to DC InputåÊto preserve battery charge when both sources connected

D-Box (Weapon) Demonstration:

Wooden Camera Director's Monitor Cage v2
Wooden Camera Handgrip (Right)

Wooden Camera Handgrip (Right)

by Wooden Camera
$ 195.00
Wooden Camera Handgrip (Right) is an ergonomic wooden handgrip, carved from a solid piece of Sapele wood which is similar to Mahogany. Attaches by ARRI standard rosette and M6 threaded thumbscrew. It is possible to add start/stop trigger by purchasing the Trigger Box. Left hand version is also available!

For attaching directly to rods, consider the 15mm Rod Clamp to ARRI Rosette and 19mm Rod Clamp to ARRI Rosette. Other useful items include the Rosette Arm and Rosette Arm (Short) which position the handgrip further out in front of you and the Rosette Spacer Standoff (Small) and (Large) for spacing grips off the camera body.
Wooden Camera Handgrip Trigger Box

Wooden Camera Handgrip Trigger Box

by Wooden Camera
$ 195.00

Wooden Camera Handgrip Trigger Box attaches to the Wooden Handgrip (Right) and (Left) to add start/stop functionality for LANC and ARRI 3 pin Fischer compatible cameras. The same control box works with both the Left and the Right grip. Simply remove the captured M3 screws and insert them from the opposite side. Coiled LANC Cable (12") and Coiled 3pin Fischer Cable (20") included. No power is required for operation.

Works with OMOD COMMAND, COMMAND RT and OMOD XLR via 3-pin Fischer run / stop connector.

Wooden Camera NATO Handle Kit (Plus, 100mm)
The NATO Handle Kit (Plus, 100mm) is a quick release top handle that attaches and detaches without screws. Includes NATO Handle (Plus) and Safety NATO Rail (100mm) at a reduced package price. To attach to camera, slide onto NATO rail and turn thumbscrew to lock in place. Loosen top knob to adjust grip rotation. Sideways 15mm tube clamp allows for attachment of UVF Mount v2 (No Clamp). Forward facing 15mm rod opening and 19mm rear rod opening for attaching single rods for focus motors, etc. Integrated shoe mount for attaching on camera lights, microphone shock mounts, etc. 1/4-20 and 3/8-16 holes on grip area for attaching additional accessories. 1/4-20 holes on handle front for attaching Rod Clamps which allow for pass through rods front to back.

Safety NATO Rail (100mm), included in kit, attaches to two 1/4-20 screw points spaced up to 72mm apart center to center.

PL Mount (Weapon/Epic-W/Scarlet-W/Epic/Scarlet is a simple PL mount that attaches to RED Weapon, Epic-W, Scarlet-W, Epic, and Scarlet cameras and is also compatible with Blackmagic 4K modified cameras. No lens data is passed through. Protective recessed area for RED data pins. Machined out of aircraft aluminum and PL cap is included.


IMPORTANT - this will not attach to a Blackmagic Camera without the modification procedure.

Specifications:
Weight: 216g (0.5 lbs)
Dimensions: 81.8 x 81.8 x 46.5 mm (3.2 x 3.2 x 1.8 in)

Wooden Camera Rosette Arm

Wooden Camera Rosette Arm

by Wooden Camera
$ 250.00
Rosette extension arm with ARRI style rosettes on each end. For use with Crossbar, Bolt on Rosette (ARRI), Rosette Handle, and other ARRI compatible rosette equipment. M6 adjustable thumbscrew. Extends hand grip 6.6 inches (168mm) and jogs out 1.6 inches (42mm).

Attaches directly to AJA CION, Sony FS7, Blackmagic URSA (using Blackmagic's rosette baseplate), ARRI Alexa, and ARRI Amira (using ARRI's Amira baseplate).

Includes: (1) M6 nylon spacer
Wooden Camera Shoulder Rig v2

Wooden Camera Shoulder Rig v2

by Wooden Camera
$ 1,250.00
Quick releasable shoulder rig based on ARRI standard dovetail and rosettes. New design allows for Crossbar to be adjusted left and right on the NATO standard rail by unlocking center thumbscrew. Included Rosette Arms position grips comfortably in front of your body. Arca-Swiss style dovetail underneath the ARRI standard dovetail allows shoulder pad to be adjusted forwards and backwards or quickly removed. Threaded holes on Shoulder Pad, Crossbar, and Handles for attaching accessories like monitors, rod clamps, cheeseplates, battery mounts, and more. Works great with our new NATO Lock Magic Arms for quickly moving an LCD from camera to shoulder mounted position.
Wooden Camera Unified Bridgeplate (19mm)

Wooden Camera Unified Bridgeplate (19mm)

by Wooden Camera
$ 499.00
Unified Bridgeplate (19mm) is an ARRI standard bridge plate with 19mm studio rods (rods spaced 104mm center to center). New design allows the Bridgeplate to be converted from RED standard height to ARRI standard height making it compatible with any type of camera rig. Rubberized top coating prevents twisting and slotted design accommodates non-standard screw spacings.
Wooden Camera Unified VCT Wedge Plate

Wooden Camera Unified VCT Wedge Plate

by Wooden Camera
$ 495.00
Unified VCT Wedge Plate is a Sony VCT-14 standard device that interfaces with the bottom of all Unified Baseplates. Our special reduced height dovetail shape allows each Unified camera rig to be quickly installed and balanced properly over your shoulder. Safety pin and stopper screws on the ends prevent accidental removal. Threaded M6 ARRI standard rosettes are found on each side and can be combined with our Rosette Standoffs and Rosette Arms for a quick, handheld configuration. Also present are 1/4-20 threaded holes and the ARRI standard accessory mounts (3/8-16 threaded hole with locating pins adjacent). At the rear of the wedge plate, a knob is present which can be tightened after installing onto the VCT-14 Tripod Plate to prevent any potential wiggle.

A key slot is also present on the top center for times when you might need to attach the Wedge Plate directly to the camera bottom using the included 1/4-20 and 3/8-16 low profile screws.

Note that this product is designed to work with our Unified Baseplates only and is not designed to interface with other ARRI style Bridgeplate products. If you are looking to attach an ARRI style Bridgeplate to a handheld system, please see our Shoulder Rigs.

Included:
(2) 1/4-20 Low Profile Screws
(2) 3/8-16 Low Profile Screws